Dimensions: Emblem "Leon" in the tailgate (2 and 4-door models)

Special tools and workshop equipment required

• Hot-air blower - SAT 1416-
• Digital thermometer - SAT 4013-
• Thrust piece - T20098-
• Release lever - U 30800-
• Adhesive strip remover - VAS 6349-

Removing

• Heat the self-adhesive emblem to approx. 25ºC with the hot air blower - SAT 1416- .
• Unfasten the emblem with the help of the lever - U 30800- .
• Remove possible residual adhesive with the tool - VAS 6349- .

fitting

Note

• Do not remove the protective film of the self-adhesive emblem until the assembly work on the vehicle has been completed.
• If the emblem is installed for the first time on a new vehicle or on newly painted surfaces.
• The lettering must be bonded in place immediately after cleaning.
• Remove protective film just before the installation.

• Clean the area of the tailgate where the new self-adhesive badge is to be applied with isopropyl alcohol or heptanol.
• Then treat the area where the new self-adhesive company badge should be applied using silicone cleaner.
• Allow to dry well.
• Using the hot air blower - SAT 1416- , heat the application area on the bodywork to approx. 35ºC. Check the temperature using the digital thermometer - SAT 4013- .
• Remove the protective film -2- of the self-adhesive company emblem "LEON".

Note This illustration shows dimensions in millimetres.

• Apply the new self-adhesive badge "LEON" according to the dimensions shown in the illustration.
• Apply the self-adhesive emblem -3- and press down with pressure tool - T20098- with force of approx 5 kg.
• Remove the protective film -1- of the self-adhesive emblem.

Dimensions: Emblem "FR" in the tailgate (2 and 4-door models)

Special tools and workshop equipment required

• Hot-air blower - SAT 1416-
• Digital thermometer - SAT 4013-
• Thrust piece - T20098-
• Release lever - U 30800-
• Adhesive strip remover - VAS 6349-

Removing

• Heat the self-adhesive emblem to approx. 25ºC with the hot air blower - SAT 1416- .
• Unfasten the emblem with the help of the lever - U 30800- .
• Remove possible residual adhesive with the tool - VAS 6349- .

fitting

Note

• Do not remove the protective film of the self-adhesive emblem until the assembly work on the vehicle has been completed.
• If the emblem is installed for the first time on a new vehicle or on newly painted surfaces.
• The lettering must be bonded in place immediately after cleaning.
• Remove protective film just before the installation.

• Clean the area of the tailgate where the new self-adhesive badge is to be applied with isopropyl alcohol or heptanol.
• Then treat the area where the new self-adhesive company badge should be applied using silicone cleaner.
• Allow to dry well.
• Using the hot air blower - SAT 1416- , heat the application area on the bodywork to approx. 35ºC . Check the temperature using the digital thermometer - SAT 4013- .
• Remove the protective film -2- of the self-adhesive emblem "FR".

Note This illustration shows dimensions in millimetres.

• Apply the new self-adhesive emblem "FR" -1- according to the dimensions shown in the figure.
• Attach the self-adhesive emblem "FR" -1- and press down with pressure tool - T20098- with force of approx 5 kg.

Dimensions: Emblem "CUPRA" in the tailgate (2 and 4-door models)

Special tools and workshop equipment required

• Hot-air blower - SAT 1416-
• Digital thermometer - SAT 4013-
• Thrust piece - T20098-
• Release lever - U 30800-
• Adhesive strip remover - VAS 6349-

Removing

• Heat the self-adhesive emblem to approx. 25ºC with the hot air blower - SAT 1416- .
• Unfasten the emblem with the help of the lever - U 30800- .
• Remove possible residual adhesive with the tool - VAS 6349- .

fitting

Note

• Do not remove the protective film of the self-adhesive emblem until the assembly work on the vehicle has been completed.
• If the emblem is installed for the first time on a new vehicle or on newly painted surfaces.
• The lettering must be bonded in place immediately after cleaning.
• Remove protective film just before the installation.

• Clean the area of the tailgate where the new self-adhesive badge is to be applied with isopropyl alcohol or heptanol.
• Then treat the area where the new self-adhesive company badge should be applied using silicone cleaner.
• Allow to dry well.
• Using the hot air blower - SAT 1416- , heat the application area on the bodywork to approx. 35ºC . Check the temperature using the digital thermometer - SAT 4013- .

Company badge "CUPRA"

• Remove the protective film -2- of the self-adhesive emblem "CUPRA".

Note This illustration shows dimensions in millimetres.

• Apply the new self-adhesive emblem "CUPRA" -3- according to the dimensions specified in the illustration.
• Attach the self-adhesive emblem "CUPRA" -3- and press down with pressure tool - T20098- with force of approx 5 kg.
• Remove the protective film -1- of the self-adhesive emblem.

Badge "CUPRA"

• Remove the protective film -4- of the self-adhesive emblem "CUPRA".

Note This illustration shows dimensions in millimetres.

• Apply the new self-adhesive emblem "CUPRA" -5- according to the dimensions specified in the illustration.
• Attach the self-adhesive emblem "CUPRA" -5- and press down with pressure tool - T20098- with force of approx 5 kg.

Dimensions: Emblem "Ecomotive" in the tailgate (2 and 4-door models)

Special tools and workshop equipment required

• Hot-air blower - SAT 1416-
• Digital thermometer - SAT 4013-
• Thrust piece - T20098-
• Release lever - U 30800-
• Adhesive strip remover - VAS 6349-

Removing

• Heat the self-adhesive emblem to approx. 25ºC with the hot air blower - SAT 1416- .
• Unfasten the emblem with the help of the lever - U 30800- .
• Remove possible residual adhesive with the tool - VAS 6349- .

fitting

Note

• Do not remove the protective film of the self-adhesive emblem until the assembly work on the vehicle has been completed.
• If the emblem is installed for the first time on a new vehicle or on newly painted surfaces.
• The lettering must be bonded in place immediately after cleaning.
• Remove protective film just before the installation.

• Clean the area of the tailgate where the new self-adhesive badge is to be applied with isopropyl alcohol or heptanol.
• Then treat the area where the new self-adhesive company badge should be applied using silicone cleaner.
• Allow to dry well.
• Using the hot air blower - SAT 1416- , heat the application area on the bodywork to approx. 35ºC . Check the temperature using the digital thermometer - SAT 4013- .
• Remove the protective film -2- from the new self-adhesive "Ecomotive" company badge.

Note This illustration shows dimensions in millimetres.

• Apply the new self-adhesive badge "Ecomotive" according to the dimensions shown in the illustration.
• Apply the self-adhesive emblem -3- and press down with pressure tool - T20098- with force of approx 5 kg.
• Remove the protective film -1- of the self-adhesive emblem.

Dimensions: Emblem "TGI" in the tailgate (2 and 4-door models)

Special tools and workshop equipment required

• Hot-air blower - SAT 1416-
• Digital thermometer - SAT 4013-
• Thrust piece - T20098-
• Release lever - U 30800-
• Adhesive strip remover - VAS 6349-

Removing

• Heat the self-adhesive emblem to approx. 25ºC with the hot air blower - SAT 1416- .
• Unfasten the emblem with the help of the lever - U 30800- .
• Remove possible residual adhesive with the tool - VAS 6349- .

fitting

Note

• Do not remove the protective film of the self-adhesive emblem until the assembly work on the vehicle has been completed.
• If the emblem is installed for the first time on a new vehicle or on newly painted surfaces.
• The lettering must be bonded in place immediately after cleaning.
• Remove protective film just before the installation.

• Clean the area of the tailgate where the new self-adhesive badge is to be applied with isopropyl alcohol or heptanol.
• Then treat the area where the new self-adhesive company badge should be applied using silicone cleaner.
• Allow to dry well.
• Using the hot air blower - SAT 1416- , heat the application area on the bodywork to approx. 35ºC . Check the temperature using the digital thermometer - SAT 4013- .
• Remove the protective film -2- of the self-adhesive company badge "TGI".

Note This illustration shows dimensions in millimetres.

• Apply the new self-adhesive badge "TGI" according to the dimensions shown in the illustration.
• Apply the self-adhesive emblem -3- and press down with pressure tool - T20098- with force of approx 5 kg.
• Remove the protective film -1- of the self-adhesive emblem.

Dimensions: Emblem "Leon" in the tailgate (ST model)

Special tools and workshop equipment required

• Hot-air blower - SAT 1416-
• Digital thermometer - SAT 4013-
• Thrust piece - T20098-
• Release lever - U 30800-
• Adhesive strip remover - VAS 6349-

Removing

• Heat the self-adhesive emblem to approx. 25ºC with the hot air blower - SAT 1416- .
• Unfasten the emblem with the help of the lever - U 30800- .
• Remove possible residual adhesive with the tool - VAS 6349- .

fitting

Note

• Do not remove the protective film of the self-adhesive emblem until the assembly work on the vehicle has been completed.
• If the emblem is installed for the first time on a new vehicle or on newly painted surfaces.
• The lettering must be bonded in place immediately after cleaning.
• Remove protective film just before the installation.

• Clean the area of the tailgate where the new self-adhesive badge is to be applied with isopropyl alcohol or heptanol.
• Then treat the area where the new self-adhesive company badge should be applied using silicone cleaner.
• Allow to dry well.
• Using the hot air blower - SAT 1416- , heat the application area on the bodywork to approx. 35ºC . Check the temperature using the digital thermometer - SAT 4013- .
• Remove the protective film -2- of the self-adhesive company emblem "LEON".

• Apply the new self-adhesive badge "LEON" according to the dimensions shown in the illustration.
• Apply the self-adhesive emblem -3- and press down with pressure tool - T20098- with force of approx 5 kg.
• Remove the protective film -1- of the self-adhesive emblem.

Dimensions: Emblem "FR" in the tailgate (ST model)

Special tools and workshop equipment required

• Hot-air blower - SAT 1416-
• Digital thermometer - SAT 4013-
• Thrust piece - T20098-
• Release lever - U 30800-
• Adhesive strip remover - VAS 6349-

Removing

• Heat the self-adhesive emblem to approx. 25ºC with the hot air blower - SAT 1416- .
• Unfasten the emblem with the help of the lever - U 30800- .
• Remove possible residual adhesive with the tool - VAS 6349- .

fitting

Note

• Do not remove the protective film of the self-adhesive emblem until the assembly work on the vehicle has been completed.
• If the emblem is installed for the first time on a new vehicle or on newly painted surfaces.
• The lettering must be bonded in place immediately after cleaning.
• Remove protective film just before the installation.

• Clean the area of the tailgate where the new self-adhesive badge is to be applied with isopropyl alcohol or heptanol.
• Then treat the area where the new self-adhesive company badge should be applied using silicone cleaner.
• Allow to dry well.
• Using the hot air blower - SAT 1416- , heat the application area on the bodywork to approx. 35ºC . Check the temperature using the digital thermometer - SAT 4013- .
• Remove the protective film -2- of the self-adhesive emblem "FR".

• Apply the new self-adhesive emblem "FR" -1- according to the dimensions shown in the figure.
• Attach the self-adhesive emblem "FR" -1- and press down with pressure tool - T20098- with force of approx 5 kg.

Dimensions: Emblem "Ecomotive" in the tailgate (ST model)

Special tools and workshop equipment required

• Hot-air blower - SAT 1416-
• Digital thermometer - SAT 4013-
• Thrust piece - T20098-
• Release lever - U 30800-
• Adhesive strip remover - VAS 6349-

Removing

• Heat the self-adhesive emblem to approx. 25ºC with the hot air blower - SAT 1416- .
• Unfasten the emblem with the help of the lever - U 30800- .
• Remove possible residual adhesive with the tool - VAS 6349- .

fitting

Note

• Do not remove the protective film of the self-adhesive emblem until the assembly work on the vehicle has been completed.
• If the emblem is installed for the first time on a new vehicle or on newly painted surfaces.
• The lettering must be bonded in place immediately after cleaning.
• Remove protective film just before the installation.

• Clean the area of the tailgate where the new self-adhesive badge is to be applied with isopropyl alcohol or heptanol.
• Then treat the area where the new self-adhesive company badge should be applied using silicone cleaner.
• Allow to dry well.
• Using the hot air blower - SAT 1416- , heat the application area on the bodywork to approx. 35ºC . Check the temperature using the digital thermometer - SAT 4013- .
• Remove the protective film -2- from the new self-adhesive "Ecomotive" company badge.

• Apply the new self-adhesive badge "Ecomotive" according to the dimensions shown in the illustration.
• Apply the self-adhesive emblem -3- and press down with pressure tool - T20098- with force of approx 5 kg.
• Remove the protective film -1- of the self-adhesive emblem.

Dimensions: Emblem "4Drive" in the tailgate (ST model)

Special tools and workshop equipment required

• Hot-air blower - SAT 1416-
• Digital thermometer - SAT 4013-
• Thrust piece - T20098-
• Release lever - U 30800-
• Adhesive strip remover - VAS 6349-

Removing

• Heat the self-adhesive emblem to approx. 25ºC with the hot air blower - SAT 1416- .
• Unfasten the emblem with the help of the lever - U 30800- .
• Remove possible residual adhesive with the tool - VAS 6349- .

fitting

Note

• Do not remove the protective film of the self-adhesive emblem until the assembly work on the vehicle has been completed.
• If the emblem is installed for the first time on a new vehicle or on newly painted surfaces.
• The lettering must be bonded in place immediately after cleaning.
• Remove protective film just before the installation.

• Clean the area of the tailgate where the new self-adhesive badge is to be applied with isopropyl alcohol or heptanol.
• Then treat the area where the new self-adhesive company badge should be applied using silicone cleaner.
• Allow to dry well.
• Using the hot air blower - SAT 1416- , heat the application area on the bodywork to approx. 35ºC . Check the temperature using the digital thermometer - SAT 4013- .
• Remove the protective film -2- of the self-adhesive company emblem "4Drive".

• Apply the new self-adhesive badge "4Drive" according to the dimensions shown in the illustration.
• Apply the self-adhesive emblem -3- and press down with pressure tool - T20098- with force of approx 5 kg.
• Remove the protective film -1- of the self-adhesive emblem.

Measurements: Emblem "X-PERIENCE" in the rear lid (ST model)

Special tools and workshop equipment required

• Hot-air blower - SAT 1416-
• Digital thermometer - SAT 4013-
• Thrust piece - T20098-
• Release lever - U 30800-
• Adhesive strip remover - VAS 6349-

Removing

• Heat the self-adhesive emblem to approx. 25ºC with the hot air blower - SAT 1416- .
• Unfasten the emblem with the help of the lever - U 30800- .
• Remove possible residual adhesive with the tool - VAS 6349- .

fitting

Note

• Do not remove the protective film of the self-adhesive emblem until the assembly work on the vehicle has been completed.
• If the emblem is installed for the first time on a new vehicle or on newly painted surfaces.
• The lettering must be bonded in place immediately after cleaning.
• Remove protective film just before the installation.

• Clean the area of the tailgate where the new self-adhesive badge is to be applied with isopropyl alcohol or heptanol.
• Then treat the area where the new self-adhesive company badge should be applied using silicone cleaner.
• Allow to dry well.
• Using the hot air blower - SAT 1416- , heat the application area on the bodywork to approx. 35ºC . Check the temperature using the digital thermometer - SAT 4013- .
• Remove the protective film -2- from the new self-adhesive company emblem "X-PERIENCE".

• Apply the new self-adhesive badge "X-PERIENCE" according to the dimensions shown in the illustration.
• Apply the self-adhesive emblem -3- and press down with pressure tool - T20098- with force of approx 5 kg.
• Remove the protective film -1- of the self-adhesive emblem.

Dimensions: Emblem "TGI" in the tailgate (ST model)

Special tools and workshop equipment required

• Hot-air blower - SAT 1416-
• Digital thermometer - SAT 4013-
• Thrust piece - T20098-
• Release lever - U 30800-
• Adhesive strip remover - VAS 6349-

Removing

• Heat the self-adhesive emblem to approx. 25ºC with the hot air blower - SAT 1416- .
• Unfasten the emblem with the help of the lever - U 30800- .
• Remove possible residual adhesive with the tool - VAS 6349- .

fitting

Note

• Do not remove the protective film of the self-adhesive emblem until the assembly work on the vehicle has been completed.
• If the emblem is installed for the first time on a new vehicle or on newly painted surfaces.
• The lettering must be bonded in place immediately after cleaning.
• Remove protective film just before the installation.

• Clean the area of the tailgate where the new self-adhesive badge is to be applied with isopropyl alcohol or heptanol.
• Then treat the area where the new self-adhesive company badge should be applied using silicone cleaner.
• Allow to dry well.
• Using the hot air blower - SAT 1416- , heat the application area on the bodywork to approx. 35ºC . Check the temperature using the digital thermometer - SAT 4013- .
• Remove the protective film -2- of the self-adhesive company badge "TGI".

• Apply the new self-adhesive badge "TGI" according to the dimensions shown in the illustration.
• Apply the self-adhesive emblem -3- and press down with pressure tool - T20098- with force of approx 5 kg.
• Remove the protective film -1- of the self-adhesive emblem.

Dimensions: "CUPRA" emblem on the tailgate

Special tools and workshop equipment required

• Hot-air blower - SAT 1416-
• Digital thermometer - SAT 4013-
• Thrust piece - T20098-
• Release lever - U 30800-
• Adhesive strip remover - VAS 6349-

Removing

• Heat the self-adhesive emblem to approx. 25ºC with the hot air blower - SAT 1416- .
• Unfasten the emblem with the help of the lever - U 30800- .
• Remove possible residual adhesive with the tool - VAS 6349- .

fitting

Note

• Do not remove the protective film of the self-adhesive emblem until the assembly work on the vehicle has been completed.
• If the emblem is installed for the first time on a new vehicle or on newly painted surfaces.
• The lettering must be bonded in place immediately after cleaning.
• Remove protective film just before the installation.

• Clean the area of the tailgate where the new self-adhesive badge is to be applied with isopropyl alcohol or heptanol.
• Then treat the area where the new self-adhesive company badge should be applied using silicone cleaner.
• Allow to dry well.
• Using the hot air blower - SAT 1416- , heat the application area on the bodywork to approx. 35ºC . Check the temperature using the digital thermometer - SAT 4013- .

Company badge "CUPRA"

• Remove the protective film -2- of the self-adhesive emblem "CUPRA".

Note This illustration shows dimensions in millimetres.

• Apply the new self-adhesive emblem "CUPRA" -3- according to the dimensions specified in the illustration.
• Attach the self-adhesive emblem "CUPRA" -3- and press down with pressure tool - T20098- with force of approx 5 kg.
• Remove the protective film -1- of the self-adhesive emblem.

Badge "CUPRA"

• Remove the protective film -4- of the self-adhesive emblem "CUPRA".

Note

This illustration shows dimensions in millimetres.

• Apply the new self-adhesive emblem "CUPRA" -5- according to the dimensions specified in the illustration.
• Attach the self-adhesive emblem "CUPRA" -5- and press down with pressure tool - T20098- with force of approx 5 kg.